Ds-7604 инструкция

You can also adjust the image parameters like BrightnessContrastSaturation and sharpness by dragging the corresponding icon. Note: You must click the Apply button after adjusting the configuration of each tab before you move on to adjust another one. Click the Detect button to start the detection. Sao Tome and Principe. Making more coffee straight away? Selecting Video Clips Video clips can be selected for backup in the Playback Interface using the controls found in the Mark Clip For Export panel, shown in Figure Page Checking The Status Of Your Nvr. You can click the Network button to check the network information and you can configure the network settings in this interface Figure Network Settings Menu To export network packet: By connecting the NVR to network, the captured network data packet can be exported to USB-flash disk, SATA CD-RW and other local backup devices.

DS Ni SE p Firmware_Yaelp Search

Check the corresponding checkbox of other channels to copy the record schedule to. You can click the Network button to check the network information and you can configure the network settings in this interface Figure Network Settings Menu To export network packet: By connecting the NVR to network, the captured network data packet can be exported to USB-flash disk, SATA CD-RW and other local backup devices. Hikvision assumes no responsibility or liability for any errors or inaccuracies that may appear in the book. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. Figure 39 Record Information Menu 4. Operating Your NVR There are numerous ways to navigate and operate your NVR. DOWNLOAD PORTAL - hikvisioneurope. To export NVR configuration: 1. Url of this page:. Select the Event Type you want to search. To update the system firmware from a USB storage device: 1. To playback recordings from multiple channels: 1. Page Configuring Ddns. Page Configuring Exceptions. Check the Enable VCA Alarm checkbox. Page Network Detection. Set the operation permission of Local Configuration, Remote Configuration and Camera Configuration for the user. Select the camera to setup OSD configuration in using the camera dropdown list. Search for recorded files using the File Management menu. Choose Full Detection or Key Area Detection.

Choose Full Detection or Key Area Detection. Select the HDD tab to enter the HDD Information menu to view the HDD status, free apace, capacity, etc, as shown in Figure Page Configuring Holiday Settings. Select the HDD you want to configure in the dropdown list. ESC: Exit Soft Keyboard. You can use a combination of numbers, lowercase, uppercase and special characters for your password with at least two kinds of them contained.

Slim Application Error

Pan and tilt PTZ by clicking on the directional buttons. To access the system logs and search for these events: 1. Follow the steps to configure the holiday settings. If the same schedule can be applied in other days, click Copy. Page Disk Management. Figure 61 Main Menu Click on the Password Key button in the menu shown below. The right hand side level indications correspond to smaller cups 80 ml fig. Front Panel The following figure shows the front panel of NVR: Figure 3 NVR Front Panel The items on the front panel include: Status Indicators I have the latest firmware. To playback recordings from multiple channels: 1. Enter the destination address in the text field of Destination Address. Page Setting Camera Order. Speed Up Button: Button to increase play speed. Select the Alarm Output tab, as shown in Figure Page Viewing System Logs. To acquire the time and date over an NTP Network Time Protocol Server, check the Enable NTP checkbox. Click the Lock icon for the selected file. In Playback mode, it can be used to play or pause the video. To enable HDD sleeping: 1. In a 2x2 mode, this will show the next four display. Click on the red box area to enter the password recovery menu. Figure 88 HDD Information 2.

Note: All the parameters should be exactly the same as the PTZ camera parameters. Select the camera to configure from the camera dropdown list. Select the HDD you want to configure in the dropdown list. The PoE interface supports Plug-and-Play function. Select the camera to setup OSD configuration in using the camera dropdown list. Page Searching For Event Files. The ENTER button is used to confirm selection in any of the menu modes.

Пример заполнения формы 0503160 за 2013 год

Select the Network tab to enter the Network Information menu to view the network information, as shown in Figure Page Managing System. Figure 61 Main Menu Click on the Password Key button in the menu shown below. This field is required This field is required This field is required. Restoring Default Settings To restore factory default settings to your NVR: 1. To format a new disk: 1. In Playback mode, it can be used to play or pause the video. Select a HDD and click to pop up the Local HDD Settings menu as shown in Figure Search Product Hikvision Product Selector. Click the Apply button to save settings and click OK to exit. Network Camera EasyIP 3. Page Managing Hdd Group. If the schedule can also be applied to other days, click Copy. Highlight IMS Research Ranking Partners Disclaimer for Unauthorized Distributor VMS Partnership Standards Support Security Center Download White Paper Others Privacy Policy Online Inquiry Contact Us. Batteries are fresh and not out of charge. Page Configuring Network Settings. Selecting the Cancel button without clicking Apply or OK will quit out of the menu without saving settings. Click OK to back to the previous menu.


Hangzhou Hikvision Digital Technology Co. Ltd.

To customize display settings: 1. In PTZ control settings, press the button and then you can call a PTZ preset by pressing Numeric button. They include: Name Function Description POWER Figure 63 Main Menu Page Live Feed. You can select recording type for each period. Click the Apply button to save the settings and click to exit out of the menu. Front Panel The following figure shows the front panel of NVR: Figure 3 NVR Front Panel The items on the front panel include: Status Indicators Restoring Default Settings To restore factory default settings to your NVR: 1. Check the corresponding checkbox of other channels to copy the record schedule to. Select the HDD tab to enter the HDD Information menu to view the HDD status, free apace, capacity, etc, as shown in Figure Verification: please type the numbers you see in the box to the right This field is required submit. Figure 80 Protocol Management Settings Menu 6. To export NVR configuration: 1. Page Record Settings. Войти: Каталог бесплатных инструкций. Select the Alarm Output tab, as shown in Figure Enter the old password in the Old Password textbox. Search Product Hikvision Product Selector.


Ds-7604 инструкция - двух томах

Once enabled, the regular feed will be shown in the lower right corner while the zoomed in view will be shown on the full screen. To search for recorded files using the Playback Interface: 1. Digital Zoom Mode: Enable digital zoom on the selected channel. The combination of username and password is incorrect. Enter the Manual Record setting menu. Текст отзыва Ваше имя:. Page Managing Files. After an acceptable password has been created, a confirmation message will appear on the screen Figure 7. Select the Arming Schedule tab, as shown in Figure To export recorded files, connect a USB storage device to the NVR, select the recorded files to export and click the Export button.

Ds-7604 инструкция

5 Comments

  1. Если ты будешь наблюдать за ними во время их секса они не будут против. Им больше всего нужно чтобы на них смотрели сотни глаз и были направлены множество объективов. Ни капли смущения, чистая эротика и секс на сцене. Все начиная от легкой эротики кончая жесткими оргиями прямо на сцене зала. Посмотри и ты сейчас!

Добавить комментарий

Ваш e-mail не будет опубликован. Обязательные поля помечены *